Latest Products
Sort by
Show result

HAKKO 907 Soldering Iron Handpiece (Compatible) for HAKKO 936 HAKKO 937 HAKKO 928 HAKKO 926 Soldering Station with A1321 Heating Element

FEATURES

  • Very light and suitable for long hours operation
  • Stable working performance and long lifespan
  • Ceramic heating element which can use for a long hours operation
  • Compatible with Hakko 907 / ESD
  • For model Hakko 936, Hakko 937, Hakko 928, Hakko 926

SPECIFICATIONS

  • Voltage : DC 24V, 50W
  • Connector : 5 pins
  • Temperature range : 120 - 480 degree celsius
  • Length :190mm 
  • Weight : 44g
  • For Model : Hakko 936, Hakko 937, Hakko 928, Hakko 926 soldering station

NOTE : Tested and checked before shipment

PACKAGE CONTENT : 1 x Compatible Hakko 907 Soldering Handpiece

RM14.30

LM1458 / LM1458CN / TA75458P / NJM1458 / HA17458 Dual Operational Amplifiers, Op-Amp, DIP-8

  • IC LM1458 / LM1458CN / TA75458P
  • PACKAGE / CASE : 8-DIP
  • BRAND : Major Brand
  • IC will be tested before shipment

PACKAGE CONTENT : 1 x LM1458 / LM1458CN / TA75458P / NJM1458 / HA17458

RM1.40

QUAD CMOS 2-INPUT NOR GATE

  • IC CD4001BE / HCF4001BE / CD4001 / HEF4001B / TC4001BP
  • PACKAGE / CASE : 14-DIP
  • BRAND : MAJOR BRAND
  • IC WILL BE TESTED BEFORE SHIPMENT

PACKAGE CONTENT : 1 x CD4001BE / HCF4001BE / CD4001 / HEF4001B / TC4001BP

RM1.50

The SG90 micro servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places. Of course, it is not nearly as strong as a standard servo. Works great with the Motor Shield for Arduino or by just wiring up with the Servo library. 

To control with an Arduino, we suggest connecting the orange control wire to pin 9 or 10 and using the Servo library included with the Arduino IDE. Position "0" (1.5ms pulse) is middle, "90" (~2ms pulse) is all the way to the right, "-90" (~1ms pulse) is all the way to the left.

SPECIFICATIONS

  • Model : SG90
  • Weight : 9g
  • No-load / Operating Speed : 0.12 seconds / 60 degrees (4.8V)
  • Working Frequency : 50Hz
  • Dead-set: 7 microseconds
  • Stall Torque : 1.2 - 1.4 kg / cm (4.8V)
  • Motor Type: Brushed DC Motor
  • Gear Type: Plastic Gears
  • Case Material: Plastic
  • Control Mode : PWM
  • Connector Wire Length : 24.0cm (9.4 inch)
  • Operating Temperature: -30 to +60 degrees Celsius
  • Operating voltage: 4.8V-7.2V

The wire colors are :

  • Red = Battery(+) 
  • Brown = Battery(-) 
  • Orange = Signal

PACKAGE CONTENT : 1 x SG90 9G Micro Servo with Accessories, 1 x SG90 Bracket

TECHNICAL REFERENCE 

Tutorial #1 : https://www.instructables.com/id/How-to-usa-a-Servo-motor-Arduino-Tutorial/

Tutorial #2 : https://www.instructables.com/id/Arduino-How-to-Control-Servo-Motor-With-Arduino/

RM5.10

This is a momentary push button switch that made of high temperature resistance materials meeting ROHS requirements. It is durable and long usage life cycle switch. It is widely used in computers, remote controller, digital products, communications products, household appliances, toys, fitness equipment, medical equipment and etc.

MODEL : B3F-4055

VARIANT : OMRON (YELLOW) AND CHINA OEM (BLACK)

SPECIFICATIONS

  • Dimension : 12 x 12 x 7.3mm excluding pins (L * W * H)
  • Button Dimension : 3.8 x 3.8mm
  • Contact Form : N.O., SPST
  • Pin Number : 4 pins
  • Pin Pitch : 12.5 x 5mm (L * W)
  • Pin Length : 3.5mm 
  • Material : Plastic, Metal 
  • Main Color : Black
  • Net Weight : 0.85g

PACKAGE CONTENT : 1 x Momentary Tactile Push Button Switch

NOTE : The cap for the switch is not included

RM0.30

The AA size battery holder can hold 4 x 1.5V AA size batteries and can be used as a 4.8V rechargeable or 6V ordinary (non-rechargeable) batteries pack for your various projects as it comes with a pre-soldered 2.1mm DC power jack / plug that easily plugs in into any female DC power jack / socket. The 23cm wires are terminated with a standard 5.5×2.1mm, center positive DC power jack / plug connector.

SPECIFICATIONS

  • Voltage : 6V (Non-rechargeable batteries) or 4.8V (Rechargeable batteries)
  • Material : ABS Plastic
  • Power : 4 x 1.5V AA batteries
  • Connection : Series
  • Color : Black
  • Plug : DC2.1mm type
  • Cable Length : 23cm
  • Net Weight : 21g
  • Dimension : 58mm x 62mm x 16mm (L*W*H)
  • Batteries not included

PACKAGE CONTENT : 1 x 4 Cells / Slots 4 x AA 1.5V Battery Holder Casing with 5.5 x 2.1mm DC Power Jack / Plug

RM1.70

The AA size battery holder can hold 6 x 1.5V AA size batteries and can be used as a 7.2V rechargeable or 9V ordinary (non-rechargeable) batteries pack for your various projects as it comes with a pre-soldered 2.1mm DC power jack / plug that easily plugs in into any female DC power jack / socket. The 12cm wires are terminated with a standard 5.5×2.1mm, center positive DC power jack / plug connector.

SPECIFICATIONS

  • Voltage : 9V (Non-rechargeable batteries) or 7.2V (Rechargeable batteries)
  • Material : ABS Plastic
  • Power : 6 x 1.5V AA batteries
  • Connection : Series
  • Color : Black
  • Plug : DC2.1mm type
  • Cable Length : 12cm
  • Net Weight : 25g
  • Dimension : 58mm x 90mm x 15mm (L*W*H)
  • Batteries not included

PACKAGE CONTENT : 1 x 6 Cells / Slots 6 x AA 1.5V Battery Holder Casing with 5.5 x 2.1mm DC Power Jack / Plug

RM4.30

This 18650 battery holder holds three (3) 18650 lithium-ion batteries connected in series, providing approximately 11.1V output (~3.7V x 3). Ideal for battery powered projects, and come with a lead wires.

FEATURES

  • High-quality plastic holder
  • Small size, easy to carry
  • Takes 3 standard size 18650 batteries side by side to form a compact battery of 3.7V x 3 = 11.1V
  • Embossed polarity marks

SPECIFICATIONS

  • Material : ABS
  • Color : Black
  • Connection : Series
  • Battery Type: 3 x 18650
  • Weight : Approx. 21g
  • Dimensions: 7.70 cm x 6.10 cm x 2.10 cm (L x W x H)

PACKAGE CONTENT : 1 x 18650 Three Cells / Slots 3.7V Lithium Battery Holder with Lead Wires

RM2.90

BRAND : PRETUL

2-in-1 Heavy Duty Adjustable and Self-Adjusting Automatic Wire Cable Stripper with Wire Cable Cutter ( Stripping / Cutting )

These automatic wire stripper is our most universal, stripping from 0.2~5.5mm² wire with adjustable and self-adjusting jaw system that won't damage PVC insulation.

  • The automatic wire stripper is heavy duty, durable and convenient to operate 
  • 2-in-1, cut and strip solid or stranded 10-24 AWG wires
  • The automatic wire stripper can automatically adjusts to wire size
  • The automatic wire stripper is able to strip single core or multiple core wires
  • Adjustable blade force
  • Adjustable stop for wire length
  • Single core wire stripping range : 0.2~3.3mm² 
  • Multi core wire stripping range : 0.2~5.5mm² 
  • Flat wire stripping range : 0.2~3.5mm² 
  • Single core wire cutting range : 0.08~2.0mm² 
  • Multi core wire cutting range : 0.09~3.5mm² 
  • Flat wire cutting range : 8mm²  (max)
  • Adjustable wire stripping length : 2mm~20mm
  • Material : Chrome Vanadium Steel + Plastic
  • Overall length: 173mm
  • Handle length: 125mm
  • Weight: 160g

Note : During wire / cable stripping, make sure the insulation of the wire / cable is not aging. Aging wire / cable might cause the PVC insulation of the wire / cable become very stiff and hard. The stiffness and hardness of the PVC insulator will need increase the blade pressure on the wire subsequently may lead to improper stripping or wire / cable broken.

PACKAGE CONTENT : 1 x 2-in-1 Heavy Duty Adjustable and Self-Adjusting Automatic Wire Cable Stripper with Wire / Cable Cutter

RM13.50

FEATURES

  • 100% brand new 
  • No electrical tap, No splicing, no crimping, but only a small screw driver
  • DC power plug / jack / adapter / connecotr with plastic construction and strain relief
  • It is a perfect solution for those who want to make custom power cable
  • This DC power jack / plug / connector / adapter provides a great connection
  • Used for  : CCTV camera, electronic projects and etc.

SPECIFICATIONS

  • 2.1 x 5.5mm DC power plug / jack / adapter / connector with screw terminal
  • Voltage range : 5V-42V
  • Internal diameter of the plug : 2.1mm
  • External diameter of the plug : 5.5mm
  • Connection : Internal is positive, external is negative or ground
  • Dimension : Approx. 39 x 13 x 12mm 
  • Color : Black, green

PACKAGE CONTENT : 1 x Female DC Power Jack Adapter Plug Connector

RM0.80

Voltage sensor / detection module, a simple but very useful module which uses a voltage divider to reduce any input voltage by a factor of 5. This allows you to use the analogue input of a microcontroller to monitor voltages much higher than it capable of sensing. For example with a 0-5V Arduino analogue input voltage range you are able to measure a voltage up to 25V. The module also includes convenient screw terminals for easy and secure connection of a wire.

Voltage sensor / detection module is based on the principle of voltage divider rule, it can make the red terminal connector input voltage to 5 times smaller. Arduino analog input voltages up to 5V. The voltage detection module input voltage not greater than 5V x 5=25V (if using 3.3V systems, input voltage not greater than 3.3V x 5=16.5V).

It has the limit of Arduino analog input  5V only. So if you wish to measure higher voltages,  you will need to resort to another means.  One way is to use a voltage divider.  It is fundamentally a 5:1 voltage divider using a 30k and a 7.5k ohm resistors.

For example, Arduino AVR chips have 10-bit AD, so this module simulates a resolution of 0.00489V (5V/1023), so the minimum voltage of input voltage detection module is 0.00489V x 5 = 0.02445V.

Note: Keep in mind, you are restricted to voltages that are less than 25V. More than that and you will exceed the voltage limit of your Arduino input.

SPECIFICATIONS

  • Input voltage range : DC 0 to 25 V
  • Voltage detection range : DC 0.02445 V to 25 V
  • Analog voltage resolution : 0.00489 V
  • Divider ratio : 5:1
  • Resistor tolerance : 1%
  • Resistor value : 30k / 7.5k Ohm
  • Output interface : “+ ” connected 5/3.3V, “-” connected GND, “s” connected Arduino AD pins
  • I2C 1602 LCD can be used to display voltage
  • By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery
  • Dimensions : 28 x 14 x 13 mm (L x W x H)
  • Weight : 4g

TECHNICAL REFERENCE

Tutorial : https://www.instructables.com/id/Voltage-Measurement-Using-Arduino/

PACKAGE CONTENT : 1 x Voltage sensor / detection module

RM1.80

SAMWA Analog Multimeter / Analog Multitester with Buzzer and LED Indicator 

MODEL : YX-360TRE-L-B

BRAND : Samwa

FREE : 1 x Protective Rubber Holster

  • Wide Visual Angle for Easy Readout
  • Continuity Check with Buzzer/LED Indicator
  • 20kΩ/ V DC, 9kΩ/ V AC sensitivity.
  • DC Voltage : 0.25 / 0.5 / 2.5 / 10 / 50 / 250 / 1000V ±3%f.s; (1000V ±5%f.s)
  • AC Voltage : 10 / 50 / 250 / 1000V ±4%f.s; (1000V ±5%f.s)
  • DC Current : 100μ / 2.5m / 25m / 0.25A ±3%f.s
  • Resistance : x1 (0-0.2Ω-2kΩ) / x10 (0-2Ω-20kΩ) / x100 (0-20Ω-200kΩ) / x1k (0-200Ω-2MΩ) / x 10k (0-2kΩ-20MΩ) ±3% of accuracy
  • Decibels : -10dB~+22dB 
  • Leakage Current (Iceo)(L1) : 0-150µA x 10 range; 0-1.5mA x 10 range; 0-15mA x 10 range; 0-150mA x 10 range
  • Terminal to Terminal Voltage (LV) : Common to each Ω range; 3V-0V (Reverse of L1 scale)
  • Dimension : 150(L) x 100(W) x 35(H)mm
  • Weight : Approx. 155g 
  • Accessories : 1 x protective rubber holster, 1 x instruction manual and 1 x test leads set.
  • Batteries not included
  • 1 year local supplier warranty against manufacturing defects
RM17.80

Want to learn how traffic light works? With this module, you are able to control and simulate a simple traffic light by your own program. This module is compatible with any microcontroller such as Arduino, Raspberry Pi, Micro:Bit and etc. The LEDs used in this module is common cathode LED so you just need four wires to the controller and logic high will trigger/activate the respective LED.

Traffic Light is one of popular electronic project among final year projects and RBT (Reka Bentuk Teknologi). Modeling or simulating an actual traffic light sytem just get easier.

It is being arranged to be same as normal traffic light where the Red is at top, Yellow at middle and Green at bottom. Additionally, this board uses 5mm (diameter) size LED, offering clear view of the light even in compact size. Not to forget all three LEDs are diffused type so widening the viewing angle too.

SPECIFICATIONS

  • LED Traffic Light Simulation module
  • LED Colors : Red, Yellow and Green
  • LED Current Rating : Red 13mA; Yellow 13mA; Green 25mA
  • Ready with 4-way header pin, label :
    • G -> Green LED
    • Y ->Yellow LED
    • R -> Red LED
    • GND -> Common Ground (Common Cathode)
  • Compatible with 3.3V or 5V controller: Arduino, Raspberry Pi, Micro:Bit and other Microcontrollers / Microprocessors
  • 5mm diffused type LED
  • Logic high to activate LED
  • Compatible with PWM signal to control brightness

TECHNICAL REFERENCE 

Tutorial : https://fluxworkshop.com/blogs/getting-started/lets-workshop-traffic-light-module

PACKAGE CONTENT : 1 x LED Traffic Light Simulation Module

RM2.40

This is a 5V, 10A 2-Channel Relay Module. It can be used to control various appliances, and other equipments with large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, Raspberry Pi, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

It has a 1x4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays. The pins are marked on the PCB:

  • GND - Connect 0V to this pin.
  • IN1 - Controls relay 1, Active Low. Relay will turn on when this input goes below about 2.0V
  • IN2 - Controls relay 2, Active Low. Relay will turn on when this input goes below about 2.0V
  • VCC - Connect 5V to this pin. Is used to power the opto couplers

There is a second 1x3 (2.54mm pitch) pin header for supplying the "relay side" of the board with 5V. At delivery, a jumper is present on this header selecting the 5V signal from the 1x4 pin header to power the relays. For default operation, don't change this jumper!

SPECIFICATIONS

  • 5V 2-Channel relay module and each one needs 15-20mA driver current
  • Works with logic level signals from 3.3V or 5V devices
  • Supply voltage: DC5V
  • Relay type : SPDT, a common terminal, a normally open, one normally closed terminal  
  • Maximum current rating : 10A
  • Maximum voltage rating : AC250V, DC30V
  • Capable of controlling large current various appliances
  • Standard interface that can be controlled directly by microcontroller (Arduino, Raspberry Pi, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)  
  • Build in 2 units of Opto-Isolator IC 817C
  • It activates on low level

TECHNICAL REFERENCE 

Tutorial #1 : https://www.instructables.com/id/Arduino-2-Channel-Relay/

Tutorial #2 : https://www.instructables.com/id/Controlling-Any-Device-Using-a-Raspberry-Pi-and-a-/

Tutorial #3 : https://howchoo.com/g/m2qwmte5nzk/how-to-use-a-relay-with-a-raspberry-pi

Package Content : 1 x 2 Channel 5V Relay Module with Optocoupler

RM4.70

This 9V battery snap / connector with DC power supply jack / plug is a very useful connector, on one end is snap for the 9V battery, and another end is the standard DC power supply jack (2.1mm). If you are using 9V battery to power your Arduino board, this cable is very handy and perfect for you.

SPECIFICATIONS

  • Custom made to deliver power from 9V battery to DC power supply socket (2.1mm) on Arduino board
  • One end is 2.1mm DC jack / plug (center positive) and another end is snap for 9V battery
  • Cable length ~ 11cm

Package Content : 1 x 9V battery snap / connector with DC power supply jack / plug

 

RM0.90